Flowers from tameran

Flowers from tameran

Flowers from tameran Flowers from tameran 3 Flowers from tameran 2


To work we need:

Plastic suede (Foam sheets)
Scissors, pliers, iron Bulka
The wire is thin and slightly thicker
Shadow, metal comb
The heating device (iron or flat iron)
Mold (the texture of the leaf of a rose)
Glue gun
Frame rim
Tape


 

  1. Cutting and colouring

    Cut off the plastic from the roll suede bright yellow color long strip, of a width of about 2 cm. Cut the strip into equal rectangles, then cut out the same identical petals.

    The petals should turn out a lot! About 8-10 on each small flower.

    The blade shape can be arbitrary. In our case, they resemble an oval, one part of which is cut a little.

    Future flowers look more realistic, it is best to tint foam sheets at this stage.

    For this purpose, any suitable paint, pastels and even eyeshadow!

  2.  The creation of three-dimensional form

    Curl your fingers all cut petals, as if idleness kneaded and rolled in the hands of unnecessary paper.

    Straighten the petals. This is enough to get a quite naturalistic flower.

    You can add rose petals characteristic of convexity, having worked floral Bulka (example of Bulka).

    To work best on your hot hands. If your hand is not as hot as we would like, try to heat Bulku or the petal (on this later).

  3.  Formed Bud

    To form flower buds is most convenient with the help of the glue gun.

    If you get used to working with this tool, we can estimate the instantaneous effect and beauty blossoming in the hands of rosebud!

    So, at the end of a thin wire make a loop (if you sculpt flowers from polymer clay, then you know this trick), her dripping drop of glue and wrap the wire around the first petal.

    Further, all the petals are glued alternately one on another, about the same level in height (this is important).

  4.  Sepals

    Green Tamarana cut sepals and formed the «natural» look.

    For more realism sepals of a rose we have done the following:
    — nail scissors made notches on the edges of the leaves;
    — combed the workpiece on both sides with a metal comb (for animals);
    — twisted tight flagella between fingers.

    Raskruchivayas, future sepals become quite natural form.

    By the way, we first cut out four of the sepals, as in the photo on the right. Then found out that rose has five sepals 🙂

  5.  Collect small buds

    So, we already have a bright yellow buds on the wire.

    Add some green sepals in the form of carelessly crumpled and twisted starfish.

    Just take the green part (one or two) on each wire of a flower Bud. Secured with a drop of glue the glue gun.

  6.  Add texture

    Cut on the eye green leaves of rose flower. (You can also use special cutters for marking the shape of the leaves in the polymer floristry, but we think that this is easy to do without them.)

    The texture on the petals and leaves traditionally create using Moldow — special embossed billets, shapes, castings.

    If you take mold sheet roses, green leaves from tameran will be very much like real!

    Twist the leaves before or after adding texture.

  7.  The thermoforming

    Before forming cut from tameran elements often use heat.

    Work ordinary iron or a straightener, as in the photo on the right.

    Placed on a heated ceramic surface petal, after a few seconds, taking in his hands and twisted traditional for Tamarana finger movements.

    Additionally squeezes big fingers the middle lobe, forming the volume.

    For one big Bud need 16 petals.

  8.  Collect big buds

    Take the 8 closest on the shape of the petals, put them together in a pile.

    Next, curl the petals in the form of shells, gluing them to the base. According to this principle formed the so-called «rose David Austin».

    Then glue the remaining 8 petals on top of one another, continuing to move in a spiral.

    With glue gun it comes quickly, with a cold glue process may be delayed.

  9.  Decorate with flowers headband

    When all the flowers are ready, attach them to the headband using floral tape-tape.

    This stretchy, slightly sticky on one side paper tape that is often used to hide the wire and to connect the parts.

    Flowers can be pre-weave with each other using their own wire grounds.

    Then quite fast and simple floral arrangement is attached to the decorated base (first wire, then any suitable tape).

  10. That’s all! Enjoy your creativity!

You can leave a response, or trackback from your own site.

Leave a Reply

Besucherzahler
счетчик для сайта